Zubehör & Ersatzteile
Terminator Plug
Order Number: 3750
Replacement partRequired to connect MTS devices to the PC
Replacement partRequired to connect MTS devices to the PC
LM-2 USB cable
Order Number: 3813
LM-2 patch cable to MTS devices
Order Number: 3812
To connect the LM-2 to any Innovate MTS device (e.g. LMA-3, SSI-4, TC-4, DL32 etc.)
To connect the LM-2 to any Innovate MTS device (e.g. LMA-3, SSI-4, TC-4, DL32 etc.)
LM-2 power cable 12 V
Order Number: 3808
LM-2 power cable with cig lighter plug
LM-2 power cable with cig lighter plug
LM-2 / DL-32 SD card 2GB
Order Number: 3787
Memory card for LM-2 or DL-32. SD 2GBrequired for data recording without PC
Memory card for LM-2 or DL-32. SD 2GBrequired for data recording without PC
LM-2 OBD-II Cable
Order Number: 3809
To connect the LM-2 to the vehicles OBD-II port. (As Included in the LM-2 Complete Kit) 5 1/2 ft
To connect the LM-2 to the vehicles OBD-II port. (As Included in the LM-2 Complete Kit) 5 1/2 ft
LM-2 Analog/RPM In/Out cable
Order Number: 3811
Analog Input and Output Accessory Cable for LM-2 (Needed for RPM Input).and also for output of AFR signal to feed ino ECUs
Analog Input and Output Accessory Cable for LM-2 (Needed for RPM Input).and also for output of AFR signal to feed ino ECUs
Inductive pickup clamp
Order Number: 3834
Inductive pickup clamp, for RPM pickup at ignition cable.
Can be used with LM-2, DL-32, LMA-3 (adapter cable included)
Inductive pickup clamp, for RPM pickup at ignition cable.
Can be used with LM-2, DL-32, LMA-3 (adapter cable included)
USB to serial adapter
Order Number: 3733
Adapred is required to connect our equipment to PCs without serial port (com1).
Adapter connects into USB port of PC.
Tested and approved to work without troubles, beware of low cost adapters.(shipped adapter might be different from picture)
Adapred is required to connect our equipment to PCs without serial port (com1).
Adapter connects into USB port of PC.
Tested and approved to work without troubles, beware of low cost adapters.(shipped adapter might be different from picture)
12mm to 18mm Motorcycle Bung Adapter
Order Number: 3835
Sensorcable for LM-2, 8ft
Order Number: 3810
Standard sensor cable 8ft, to connect the O² Sensor to the LMA-2
Standard sensor cable 8ft, to connect the O² Sensor to the LMA-2
Window Mount for LM-2
Order Number: 3814
High Quality window mount for LM-2
High Quality window mount for LM-2
LM-2 Carrying case
Order Number: 3836
Case for secure transport and protection of your LM-2.(Shipping without any Tools)
Case for secure transport and protection of your LM-2.(Shipping without any Tools)
Exhaust clamp for O2 sensor
Order Number: 3728
Patent-pending, Venturi-effect, tapped exhaust clamp for obtaining accurate lambda measurements in non-cat autos or other engines.Pushing the O2 sensor into the tail pipe, without this exhaust clamp, does not deliver correct results
Patent-pending, Venturi-effect, tapped exhaust clamp for obtaining accurate lambda measurements in non-cat autos or other engines.Pushing the O2 sensor into the tail pipe, without this exhaust clamp, does not deliver correct results
Sensorcable for LM-2, MTX-L 18ft
Order Number: 3828
Extended sensor cable 18ft, to connect the O² Sensor to the LMA-2
Extended sensor cable 18ft, to connect the O² Sensor to the LMA-2
HBX II Heat sink
Order Number: 3729
Heat sink to reduce max. temperature of the O² Sensor.Can be used with short bungs only, do not use with long bungs !
Heat sink to reduce max. temperature of the O² Sensor.Can be used with short bungs only, do not use with long bungs !
Bosch LSU4.2 5-wire, wide-band O2 sensor
Order Number: 3737
Standard sensor shipping with LM-2 and LC-1
Standard sensor shipping with LM-2 and LC-1
Bluetooth MTS adapter
Order Number: 1128
Using this adapter you can replace the serial wired connection to your PC, by a wireless Bluetooth connection.*
* PC requires bluetooth interface, not included.
Using this adapter you can replace the serial wired connection to your PC, by a wireless Bluetooth connection.*
* PC requires bluetooth interface, not included.